- Cover image
- Title page
- Table of Contents
- Dedication
- Copyright
- Preface
- Part 1: Transducers
- Part 2: Interfacing
- Introduction to Interfacing
- Chapter 2.1: Number systems
- 2.1.1 Binary number system
- 2.1.2 Decimal to binary conversion
- 2.1.3 Hexadecimal
- 2.1.4 Decimal to hex conversion
- 2.1.5 2’s complement
- 2.1.6 Signed numbers
- 2.1.7 Subtraction and multiplication
- 2.1.8 Binary coded decimal (BCD)
- 2.1.9 Gray code
- 2.1.10 ASCII code
- 2.1.11 Boolean algebra
- 2.1.12 Digital logic circuits
- 2.1.14 Activities
- Chapter 2.2: Computer architecture
- 2.2.1 Computer architecture
- 2.2.2 Memory
- 2.2.3 Segmented memory
- 2.2.4 Memory data
- 2.2.5 Buffers
- 2.2.6 Latches
- 2.2.7 Flip-flop
- 2.2.8 Input/Output (I/O)
- 2.2.9 Microprocessor unit (MPU/CPU)
- 2.2.10 Registers
- 2.2.11 ROM
- 2.2.12 Interrupts
- 2.2.13 Memory map
- 2.2.14 Real and protected mode CPU operation
- 2.2.16 Activities
- Chapter 2.3: Assembly language
- 2.3.1 Instruction set
- 2.3.2 Assembly language
- 2.3.3 Program execution
- 2.3.4 Assembly language program structure
- 2.3.5 Assembler directives
- 2.3.6 Code segment
- 2.3.7 Assembly language shell program
- 2.3.8 Branching
- 2.3.9 Register and immediate addressing
- 2.3.10 Memory addressing
- 2.3.11 Indirect memory addressing
- 2.3.12 Indexed memory addressing
- 2.3.14 Interrupts
- 2.3.16 Activities
- Chapter 2.4: Interfacing
- 2.4.1 Interfacing
- 2.4.2 Input/Output ports
- 2.4.3 Polling
- 2.4.4 Interrupts
- 2.4.5 Direct memory access (DMA)
- 2.4.6 Serial port
- 2.4.7 Serial port addresses
- 2.4.8 Serial port registers
- 2.4.9 Serial port registers and interrupts
- 2.4.10 Serial port baud rate
- 2.4.11 Serial port operation
- 2.4.12 Parallel printer port
- 2.4.13 Parallel port registers
- 2.4.14 Parallel printer port operation
- Chapter 2.5: A to D and D to A conversions
- 2.5.1 Interfacing
- 2.5.2 The Nyquist criterion
- 2.5.3 Resolution and quantisation noise
- 2.5.4 Oversampling
- 2.5.5 Analog to digital converters
- 2.5.6 ADC (integrating method)
- 2.5.7 ADC (successive approximation)
- 2.5.8 Aperture error
- 2.5.9 ADC08xx chip
- 2.5.10 Sample-and-hold
- 2.5.11 Sample-and-hold control
- 2.5.12 Digital to analog conversion
- 2.5.13 DAC0800
- 2.5.14 Data acquisition board
- Chapter 2.6: Data communications
- 2.6.1 Communications
- 2.6.2 Byte to serial conversion
- 2.6.3 RS232 interface
- 2.6.4 Synchronisation
- 2.6.5 UART (6402)
- 2.6.7 Line drivers
- 2.6.8 UART clock
- 2.6.9 UART Master Reset
- 2.6.10 Null modem
- 2.6.11 Serial port BIOS services
- 2.6.12 Serial port operation in BASIC
- 2.6.13 Hardware handshaking
- 2.6.14 RS485
- 2.6.15 GPIB
- 2.6.16 USB
- 2.6.17 TCP/IP
- Chapter 2.7: Programmable logic controllers
- Chapter 2.8: Data acquisition project
- Part 3: Signal processing
- Introduction to Signal processing
- Chapter 3.1: Transfer function
- Chapter 3.2: Active filters
- 3.2.1 Filters
- 3.2.2 T –network filters
- 3.2.3 Twin-T filter
- 3.2.4 Active integrator/differentiator
- 3.2.5 Integrator transfer function
- 3.2.6 Low pass filter – active
- 3.2.7 2nd order active filter
- 3.2.8 Double integrator
- 3.2.9 Bandpass filter – narrow
- 3.2.10 Differentiator transfer function
- 3.2.11 High pass filter – active
- 3.2.12 High pass filter – ω-domain
- 3.2.13 Bandpass filter – wide
- 3.2.14 Voltage gain and dB
- 3.2.16 Activities
- Chapter 3.3: Instrumentation amplifier
- Chapter 3.4: Noise
- Chapter 3.5: Digital signal processing
- 3.5.1 Digital filters
- 3.5.2 Fourier series
- 3.5.3 Fourier transform
- 3.5.4 Sampling
- 3.5.5 Discrete Fourier transform
- 3.5.6 Filtering
- 3.5.7 Digital filtering (ω-domain)
- 3.5.8 Convolution
- 3.5.9 Discrete convolution
- 3.5.10 Digital filtering (t-domain)
- 3.5.11 Example
- 3.5.12 Smoothing transfer function
- 3.5.14 Activities
- Index
- Further reading
- Parts lists
-
No Comment
..................Content has been hidden....................
You can't read the all page of ebook, please click here login for view all page.