Cover image
by V Kothari, R Alagirusamy, A. Das, A Majumdar
Process Control in Textile Manufacturing
- Cover image
- Title page
- Table of Contents
- Copyright
- Contributor contact details
- Woodhead Publishing Series in Textiles
- Foreword
- Part I: General issues
- Chapter 1: Basics of process control in textile manufacturing
- Chapter 2: Basic principles of control systems in textile manufacturing
- Chapter 3: Testing and statistical quality control in textile manufacturing
- Abstract:
- 3.1 Introduction: statistical quality control
- 3.2 Basic measurement concepts in statistical quality control
- 3.3 Interpretations: critical difference
- 3.4 Interpretations: âtâ tests, âFâ tests and the chi-square method
- 3.5 Decision-making using control charts
- 3.6 Decision-making: hypothesis testing
- 3.7 Decision-making: significance testing
- 3.8 Testing fibre and yarn properties
- 3.9 Testing fabric properties
- Raw material
- Part II: Process control in fibre production and yarn manufacture
- Chapter 4: Process and quality control in cultivating natural textile fibres
- Chapter 5: Process control in the manufacturing of synthetic textile fibres
- Chapter 6: Process control in blowroom and carding operations
- Abstract:
- 6.1 Introduction to blowroom operations
- 6.2 General process control in the blowroom
- 6.3 Process control in blowroom processes
- 6.4 Process control in carding: control of process parameters
- 6.5 Process control in carding: control of card clothing, wire maintenance and card waste
- 6.6 Yarn count issues and other common process control problems for blowroom and carding operations
- Chapter 7: Process control in drawing, combing and speed frame operations
- Abstract:
- 7.1 Introduction
- 7.2 Process control in drawing: key elements
- 7.3 The impact of drawing on yarn quality
- 7.4 Process control in drawing: common problems
- 7.5 Process control in combing: key elements
- 7.6 Process control in combing: the impact of combing on yarn quality and common problems arising from the process
- 7.7 Process control in speed frame operations: key elements
- 7.8 Process control in speed frame operations: the impact of speed frame operations on yarn quality and common defects related to the process
- 7.9 Conclusions and future trends
- 7.10 Acknowledgement
- Chapter 8: Process control in ring and rotor spinning
- Abstract:
- 8.1 Introduction
- 8.2 Factors affecting spinning tension in ring spinning
- 8.3 Control of end breakage rate in ring spinning
- 8.4 Factors affecting end breakage rates in ring spinning
- 8.5 Control of fly generation and twist variations in ring spinning
- 8.6 Process control in rotor spinning
- 8.7 Control of end breakage rate and twist loss in rotor spinning
- 8.8 Future trends
- Chapter 9: Maintenance of yarn spinning machines
- Part III: Process control in fabric manufacture, coloration and finishing
- Chapter 10: Process control in knitting
- Chapter 11: Process control in weaving
- Chapter 12: Process control in nonwovens production
- Abstract:
- 12.1 Introduction
- 12.2 Needle punching: process variables and process control
- 12.3 Hydroentanglement: process variables and process control
- 12.4 Melt blowing: process variables and process control
- 12.5 Spunbonding: process variables and process control
- 12.6 Future trends
- 12.7 Sources of further information
- 12.8 Acknowledgement
- Chapter 13: Process control in dyeing of textiles
- Chapter 14: Process control in printing of textiles
- Chapter 15: Process control in finishing of textiles
- Abstract:
- 15.1 Introduction
- 15.2 Instrumental process control
- 15.3 Textile finishing processes and process control in finishing
- 15.4 Process control in basic finishing machines
- 15.5 Process control in stenter machines
- 15.6 Calendering process
- 15.7 Surface raising and pre-shrinking finishes
- 15.8 Finishing with alkali
- 15.9 Softeners
- 15.10 Resin finishes
- 15.11 Protection from fire damage and water penetration
- 15.12 Anti-pilling finish
- 15.13 Other types of finishing: antistatic, soil release, antimicrobial and UV protection
- 15.14 Wool treatment and enzyme finishes
- 15.15 Low-liquor finishing
- 15.16 Plasma treatments
- 15.17 Future trends
- Chapter 16: Process control in apparel manufacturing
- Abstract:
- 16.1 Introduction
- 16.2 Process control in spreading, pattern making and cutting
- 16.3 Process control in sewing
- 16.4 Causes of damage to the fabric during sewing
- 16.5 Control of fusing and pressing operations, storage and packaging
- 16.6 Quality evaluation of apparel: testing for tailorability
- 16.7 Quality evaluation of apparel: testing for sewability
- 16.8 Quality evaluation of accessories
- Index
-
No Comment
..................Content has been hidden....................
You can't read the all page of ebook, please click here login for view all page.